Twin Stim Tens Unit •Channels: Dual Channel, isolated between channels •Pulse Amplitude: Adjustable, 0-100 mA peak into 500 ohm load each channel. •Voltage: 0 - 50V (Load: 500 ohm) •Pulse Rate: Adjustable, from 2 to 150 Hz, 1 Hz/step •Pulse Width: Adjustable, from 50 to 300 microseconds, 10uS/step •Wave Form: Asymmetrical Bi-Phasic Square Pulse •On Time: Adjustable, 2~90 seconds , 1 Sec./ step •Off Time: Adjustable, 2~90 seconds , 1 Sec./ step •Ramp Time: Adjustable, 1~8 seconds, 1 Sec./ step, The "On" time will increase and decrease in the setting value. •3 EMS Modes: Constant ,Synchronous, Alternate •Constant stimulation based on setting value. Only pulse width, pulse rate and timer are adjustable in this mode. "Constant" is equal to the "Normal" mode of a TENS unit. •Synchronous: Stimulation of both channels occurs synchronously. The "ON" time including "Ramp Up" and "Ramp Down" time. Therefore, the setting of ON Time should be no less than two times of the "Ramp" time in this mode. ON TIME Alternate: The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In this mode, the setting of ON Time should be no less than two times of the "Ramp" time. The OFF Time should be equal or more than the ON Time. ON TIME Ramp up + Ramp down OFF TIME ON. Ramp up + Ramp down •5 Modes: B(Burst), N(Normal), M(Modulation), SD1(Strength Duration), SD2 •Burst Mode: Burst rate: Adjustable, 0-5 � 5Hz; Pulse width adjustable, 50~300uS; Frequency fixed = 100 ...
Saturday, October 13, 2012
Twin Stim Tens Unit
Twin Stim Tens Unit Video Clips. Duration : 7.20 Mins.
Twin Stim Tens Unit •Channels: Dual Channel, isolated between channels •Pulse Amplitude: Adjustable, 0-100 mA peak into 500 ohm load each channel. •Voltage: 0 - 50V (Load: 500 ohm) •Pulse Rate: Adjustable, from 2 to 150 Hz, 1 Hz/step •Pulse Width: Adjustable, from 50 to 300 microseconds, 10uS/step •Wave Form: Asymmetrical Bi-Phasic Square Pulse •On Time: Adjustable, 2~90 seconds , 1 Sec./ step •Off Time: Adjustable, 2~90 seconds , 1 Sec./ step •Ramp Time: Adjustable, 1~8 seconds, 1 Sec./ step, The "On" time will increase and decrease in the setting value. •3 EMS Modes: Constant ,Synchronous, Alternate •Constant stimulation based on setting value. Only pulse width, pulse rate and timer are adjustable in this mode. "Constant" is equal to the "Normal" mode of a TENS unit. •Synchronous: Stimulation of both channels occurs synchronously. The "ON" time including "Ramp Up" and "Ramp Down" time. Therefore, the setting of ON Time should be no less than two times of the "Ramp" time in this mode. ON TIME Alternate: The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In this mode, the setting of ON Time should be no less than two times of the "Ramp" time. The OFF Time should be equal or more than the ON Time. ON TIME Ramp up + Ramp down OFF TIME ON. Ramp up + Ramp down •5 Modes: B(Burst), N(Normal), M(Modulation), SD1(Strength Duration), SD2 •Burst Mode: Burst rate: Adjustable, 0-5 � 5Hz; Pulse width adjustable, 50~300uS; Frequency fixed = 100 ...
Twin Stim Tens Unit •Channels: Dual Channel, isolated between channels •Pulse Amplitude: Adjustable, 0-100 mA peak into 500 ohm load each channel. •Voltage: 0 - 50V (Load: 500 ohm) •Pulse Rate: Adjustable, from 2 to 150 Hz, 1 Hz/step •Pulse Width: Adjustable, from 50 to 300 microseconds, 10uS/step •Wave Form: Asymmetrical Bi-Phasic Square Pulse •On Time: Adjustable, 2~90 seconds , 1 Sec./ step •Off Time: Adjustable, 2~90 seconds , 1 Sec./ step •Ramp Time: Adjustable, 1~8 seconds, 1 Sec./ step, The "On" time will increase and decrease in the setting value. •3 EMS Modes: Constant ,Synchronous, Alternate •Constant stimulation based on setting value. Only pulse width, pulse rate and timer are adjustable in this mode. "Constant" is equal to the "Normal" mode of a TENS unit. •Synchronous: Stimulation of both channels occurs synchronously. The "ON" time including "Ramp Up" and "Ramp Down" time. Therefore, the setting of ON Time should be no less than two times of the "Ramp" time in this mode. ON TIME Alternate: The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In this mode, the setting of ON Time should be no less than two times of the "Ramp" time. The OFF Time should be equal or more than the ON Time. ON TIME Ramp up + Ramp down OFF TIME ON. Ramp up + Ramp down •5 Modes: B(Burst), N(Normal), M(Modulation), SD1(Strength Duration), SD2 •Burst Mode: Burst rate: Adjustable, 0-5 � 5Hz; Pulse width adjustable, 50~300uS; Frequency fixed = 100 ...
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment